Crochet Baby Hat Pattern

Written byadmin in

A newborn bonnet starts with a circle small enough to rest in your palm. In this crochet baby hat pattern, you’ll work four joined rounds of double crochet, growing from 10 stitches to 40. By the end of Round 4, the crown should measure 3½ inches (about 9 cm) across. This tutorial covers the crown portion of the bonnet.

The trickiest spot is often the join. The two chains at the beginning of each crown round stand in for the first double crochet. Slip a removable stitch marker into the top of that second chain as soon as you make it. When you come back around, you’ll know exactly where to join, even if the chain has tightened and is hard to see.

If this is your first newborn bonnet, a smooth, light-colored yarn makes it easier to see where to insert your hook. After the first round, tilt the circle toward you and look for the little V at the top of each double crochet. In the following rounds, slide your hook under both strands of that V. When an increase calls for two double crochets in the same stitch, look back at the first post and insert your hook into the same opening at its base.

Crochet Baby Hat Pattern

Each crown round adds ten stitches, but the increases grow farther apart. In Round 2, every stitch receives two double crochets. In Round 3, one plain double crochet separates each pair of increases, and in Round 4, two plain double crochets separate them. If you lose your place halfway around, find the last two posts that share a base. Count the single posts worked since that increase to see what comes next.

For a more reliable size check, measure the crown in two directions. Lay it flat, measure across the center, then rotate it a quarter turn and measure again. Both readings should be close to 3½ inches (about 9 cm) at the end of Round 4. If one looks a little short, lift the crown and set it down again to release any fold before you measure. Once you’re happy with the size, jot down the yarn and hook you used so you can reproduce the same crown for another bonnet.

Stitches and abbreviations (US crochet terms)

TermMeaning
begBeginning.
ch(s)Chain(s). To chain, yarn over and draw the yarn through the loop on the hook.
yoYarn over.
dcDouble crochet. Yarn over, insert the hook into the indicated stitch, yarn over, and pull up a loop. You have 3 loops. Yarn over and pull through 2 loops, then yarn over and pull through the remaining 2.
scSingle crochet. Insert the hook into the stitch, yarn over, and pull up a loop. Yarn over and pull through both loops.
sl stSlip stitch. Insert the hook into the indicated stitch, yarn over, and draw the yarn through the stitch and the loop on the hook in one motion.
st(s)Stitch(es).
RS / WSRight side / wrong side. The RS is the face intended to show on the finished piece. The WS is the back.
Fasten offWhen directed, ch 1 and cut the yarn, leaving a 5–6 inch tail. Draw the tail through the loop on the hook and tighten gently.
* … *Repeat the instructions between the asterisks the stated number of times.
[ ]The number in brackets gives the total stitch count at the end of a row or round.

Newborn crown pattern

Choose one of the two starts below, then continue with Round 2. Both give you 10 stitches. The difference is where you place the first join.

Round 1 — Magic circle. Make a magic circle. Ch 2 to count as the first dc, then work 9 dc into the circle. Pull the starting tail to close the center. Sl st to the top of the beginning ch-2 to join. [10 sts]

Alternative Round 1 — Chain start. Ch 2. Work 10 dc into the second chain from the hook. Sl st to the first actual dc to join. For this start only, all 10 stitches come from the worked double crochets. [10 sts]

Round 2. Ch 2 and work 1 dc in the same stitch at the base of the chain. Work 2 dc in each of the next 9 stitches. Sl st to the top of the beginning ch-2. [20 sts]

Round 3. Ch 2 and work 1 dc in the same stitch. Work 1 dc in the next stitch. Then repeat *2 dc in the next stitch, 1 dc in the next stitch* 9 times. Sl st to the top of the beginning ch-2. [30 sts]

Round 4. Ch 2 and work 1 dc in the same stitch. Work 1 dc in each of the next 2 stitches. Then repeat *2 dc in the next stitch, 1 dc in each of the next 2 stitches* 9 times. Sl st to the top of the beginning ch-2. [40 sts]

Check the crown before continuing

Lay the crown on a flat surface and let the stitches relax. Measure from one outer edge straight through the center to the opposite edge. With 40 stitches and a diameter of 3½ inches, you’ve reached the checkpoint for this newborn crown. The bonnet body and edging come after this stage.

If you count 41 stitches, look first at the join. The beginning ch-2 already counts as a stitch, and the slip stitch used to close the round adds nothing to the total. If your count is correct but your circle is too wide, try the crown again with a smaller hook. If it’s too narrow, try a larger hook. Checking now takes only four rounds and gives you a measured starting point for the rest of the bonnet.

You Are Here:

We use cookies to offer you the best experience on our website. By continuing to browse, you confirm that you accept these terms.